• This forum has 505 topics, 1,378 replies, and was last updated November 23, 2022 by Chris J.
    • VMware
    • Set VM HW Version on failover VM

      Hello all, Is there a way to specify the target HW version of the failover VM?  Our source VMs are Hyper-V VMs so there isn’t a one-to-one copy so the target VM is setting it to the highest level, version 10.  We’d prefer to set the HW Version to 9.  Obviously this can be fixed […]

    • People: 4
      Replies: 4
    • August 23, 2016
    • vCenter issue scenarios

      Hi, our environment has separate Prod and a DR sites, with vCenter servers and ESXi hosts in both sites and ZVMs/VRAs in both sites. 1. If for whatever reason the DR VC server goes offline or is inaccessible, will this affect VPG replications or journal histories at all? 2. If for whatever reason. the prod […]

    • People: 2
      Replies: 4
    • July 18, 2016
    • Upgrade Zerto & VMware

      Hello All, I am facing a double upgrade dilemma and would like to see what folks’ thoughts are. We are currently running Zerto 3.5U7 on vSphere ESXi 5.5.  I have been holding off on upgrading as we wanted to do some significant testing first before rocking the boat with upgrades. So here’s my question(s) – […]

    • People: 3
      Replies: 3
    • June 21, 2016
    • VCD 8.10

      Hi there, Now that vCloud Director 8.10 is released: https://pubs.vmware.com/Release_Notes/en/vcd/8-10/rel_notes_vcloud_director_8-10.html Could you please advise when next incremental release of Zerto 4.5 with VCD 8.10 support will be available ? Regards, Mark

    • People: 4
      Replies: 5
    • June 15, 2016
    • Upgrading VMs – Zerto failback plan – use Pause?

      Hi there, We are using Zerto 3.5 u4 to replicate VMs between two sites. We are upgrading our VMs and need to come up with a failback plan using Zerto. The upgrade of the Virtual machines will take between 8 and 24 hours and we would like to be able to use Zerto to restore […]

    • People: 2
      Replies: 2
    • June 10, 2016
    • Zerto plug-in for vSphere Web Client

      In reading several documents available from Zerto that detail the configuration of the Zero plug-in for the vSphere Web Client, the instructions reference the following procedure: To set up the vSphere Web Client to work with to work with Zerto Virtual Replication: 1. When the vSphere Web Client service is installed on a Microsoft Windows […]

    • People: 3
      Replies: 8
    • May 31, 2016
    • Linux VM Test Recovery Issue

      Hello Sir. I want to change IP address of VM when I perform the ‘Test failover’. Is there any pre-requirement or limit on this job ? (vmware tools already installed and running) I didn’t find any information on the Administrator Guide and other document. VMware tools in this VM was installed and all the status […]

    • People: 2
      Replies: 2
    • May 31, 2016
    • Upgrade ESXi hosts from 4.1 to 5.5

      Hello, we have a Zerto installation between our prod site (VMware Ent. 4.1) and a DR site (also VMware 4.1). Now we are planning to upgrade both infrastructure to version 5.5 of vmware, is it possible to perform the upgrade without losing actual protection? How ? Thanks in advance, Bruno

    • People: 4
      Replies: 4
    • May 4, 2016
    • Unable to view Zerto UI using vCenter plug-in

      Hi, I’ve changed the IP address of my DR ZVM server by following the KB 00000180 and it worked fine. However, I now can no longer access the Zerto UI via the vCenter plug-in. It says “page can’t be displayed, make sure the web address https://<old ZVM IP address>:9669 is correct”. Why is it not […]

    • People: 2
      Replies: 4
    • April 26, 2016
    • Changing a VRA IP address

      Hi, I’m running ZVR v4.0 Update6. If I need to change the IP addresses of my target site VRAs, can I edit each of them in the UI and simply change their IPs? If so, what impact, if any, will this cause on the status of the VPG syncs – will it trigger a complete […]

    • People: 2
      Replies: 2
    • March 23, 2016
    • VRA helper placement

      As part of normal operations, VRA helper instances are created by ZVR. I would like to be able to influence placement of the VRA helpers in a vCenter folder or resource pool, but nothing related to VRA helpers is in the install/admin documentation. What are the possibilities for “managing” VRA helpers? Best regards, John Segers

    • People: 2
      Replies: 4
    • March 22, 2016
    • Exclude Volume from replication

      Does anyone know if there is a way to exclude a single volume when replicating a VMware Guest? The reason for this is the disk i/o on this server is so high that the replication of the pre-seeded disk never completes. What we want to do is exclude the disk with the high i/o and […]

    • People: 4
      Replies: 6
    • March 1, 2016
    • GUI view issues?

      I am noticing that after editing a VPG’s recovery datastore and letting the process complete, if I navigate to the VPG view and go over to ‘protected vms’ I still see the original datastore. Is anyone else able to replicate this? Is this just a visual bug in the gui?

    • People: 2
      Replies: 1
    • March 1, 2016

You must be logged in to create new topics. Click here to login