• This forum has 546 topics, 1,446 replies, and was last updated May 11, 2024 by Yossi A.
    • VMware
    • VM no showing up

      I am setting up a VPG and I have a VM that does not show up? Is there a way to refresh the list of VM’s

    • People: 3
      Replies: 2
    • January 23, 2016
    • What is the "CloudLogo" in Zerto v4?

      Hi, I’ve just successfully upgraded my protected and recovery sites from v3.5-U7 to v4-U3. In the new-look ZVM user interface, there’s a “CloudLogo” box in the top-left corner of the screen. What is this? Can I substitute it with my corporate logo? Is this what it’s for? Please see the attached screenshot

    • People: 2
      Replies: 2
    • December 10, 2015
    • Datacenter Migration lots of small files

      I have a VM on my existing site with a RDM, full of 7 million files small files. I need to replicate and keep this VM in step with my existing site while being able to copy out some data from the 2 disk on the New Site. I have previously tried robocopy however it takes over 24hours […]

    • People: 2
      Replies: 1
    • December 10, 2015
    • Scripted VSS Agent Install

      Hello everyone, We are looking to push out the install of the VSS agent via BigFix but I haven’t been able to figure out how to pass the ZVM information via properties of the MSI and perform a silent install.  Has anyone done this successfully?   -Alex

    • People: 2
      Replies: 1
    • December 10, 2015
    • Virtual PC

      Has anyone experimented with virtual PCs?  We are in the very beginning stages of thinking about testing virtual pcs.  We are wondering about using Zerto to protect the virtual pc server to allow business to continue in a DR situation.

    • People: 2
      Replies: 1
    • December 10, 2015
    • Migrating vcenter to a new server

      I will be moving our vcenter to a new server pretty soon my question with zeto what is involved. Will zerto need to be reconfigured from scratch, is there export/import features, does license need to be reactivated

    • People: 2
      Replies: 1
    • December 8, 2015
    • How to introduce new target ESXi hosts

      I’m running Zerto v3.5-U7 with one protected site and one recovery site, with a ZVM server in each site. I am doing an ESXi server refresh in the recovery site because my existing ESXi hosts are getting old and need replacing. I’m not sure what the exact terminology I should be using for my question […]

    • People: 3
      Replies: 7
    • November 18, 2015
    • Zerto evaluation

      Hi All I’m evaluating Zerto for a customer Business Continuity project. The solution involves one vcenter with no BC hosts (to protect only against a storage outages). I read that VRA use network and a local Journal sistem for a asyncronous replica , but what about using same hosts for replications? Does VRA uses directly […]

    • People: 3
      Replies: 2
    • September 24, 2015
    • VM Performance

      Hi All, We had 2 VMs on 2 dedicated hosts failover to 2 dedicated hosts in DR for testing The VMs appeared to failover correctly and all appeared ok but after a period of time the performance was awful to the point where the servers completely froze Both VMs had 96GB RAM and the hosts […]

    • People: 2
      Replies: 1
    • September 21, 2015
    • VPGs still initializing

      I wish there is a column the tells you how much time left before a new VPG finishes its “Initializing” state. Create new VPG, after initial flurry of WAN data transfer, the VPG is still showing “Initializing” but WAN activity has stopped. After leaving it overnight, I still see VPG protection status as “Initializing” Is […]

    • People: 1
      Replies: 1
    • September 7, 2015
    • Language Setting vCenter, ZVM Windows Server

      Hello all. When I installed ZVM(3.x and 4.0) on Windows Server Korean version, I didn’t install ZVM because of the language issue. In the case of ZVM, I can fix that issue through change the Windows server language setting or install ZVM on Windows Server English version. But, When the vCenter Server language is set […]

    • People: 2
      Replies: 2
    • August 13, 2015
    • Protect the ZVM?

      Hello all, I am off soon to my first Zerto installation (nothing special, just a couple of SQL Servers), so probably this can be a silly question. I am trying to gather as much info as I can, but one thing is not clear for me about if it is necessary to protect the ZVM […]

    • People: 3
      Replies: 3
    • July 30, 2015

You must be logged in to create new topics. Click here to login