• This forum has 544 topics, 1,443 replies, and was last updated April 29, 2024 by Steve P.
    • VMware
    • Live Failover button grayed out

      Hi Everyone,   Wondering if you’ve experience this issue before.  I was trying to do a live failover but the ‘failover’ button is grayed out!  The machines I want to failover are all synced, so I’m not too sure what would be causing it to not move forward. Any suggestions will be greatly appreciated.   […]

    • People: 2
      Replies: 3
    • January 29, 2018
    • RDM "incorrect block size" error

      I want to replicate the rdm disks connected to the running virtual server on rdm disks connected to the other esxi server.I could map an rdm disk of size 510 gb. However, although rdm drives are given in the same size, I get inrorrect block size error for 2TB size disks. Hitachi storage on the […]

    • People: 2
      Replies: 1
    • January 16, 2018
    • Destination Journal increase during maintenance

      Hi, We are in the process of doing some planned maintenance to our VMware hosts (put one into maintenance mode, patch, move on to the next etc) at our source side and during the this process, have noticed that the storage free at the destination rapidly decreases. I assume this is the journal size increasing […]

    • People: 2
      Replies: 2
    • January 16, 2018
    • Renaming recovery datastore – will it break Zerto?

      Hello everyone.  We are running Zerto 5.5U2 in VMware 6.0 on 3PAR storage and have a question: Can you rename a datastore being used by Zerto without breaking anything? Does Zerto make use of the name explicitly or the datastore GUID? Wanted to see if this is a supported action since I couldn’t find it […]

    • People: 2
      Replies: 1
    • January 12, 2018
    • Upgrading Windows vCenter from 6.0 to 6.5

      Upgrading our vCenter servers (one at Home Office and one at DR Center)  from 6.0u2 to 6.5u1 while migrating from Windows to the Virtual appliance.  Not updating hosts. We are on Zerto 5.5u2 are there any technical documents or steps to take before migrating to new vCenter appliance and from version 6.0 to 6.5   […]

    • People: 4
      Replies: 5
    • December 19, 2017
    • Zerto Cloud Connector static routes

      Hi All, I’ve deployed zerto cloud connector for one of our customers. Our CSP deployment has ZVM, ZCM on one network (managemnet) and Z-VRAs on another network (storage). Both networks are routable. ZCC had been deployed with two interfaces: customer facing netwokr and our management one. Unfortunately the static route that we should be able […]

    • People: 5
      Replies: 9
    • December 19, 2017
    • Initial Sync 100% but Still showing Initializing

      Hi Experts, I have one VM (17 TB) in my VPG and initial replication got completed in 24 hours (it was showing 32% in 23 hours but went 100% in last one hour). In Dashboard, VPG health is green and 17TB as protected but VPG status is shown as processing for last 10 hours. Please […]

    • People: 2
      Replies: 1
    • December 11, 2017
    • VRA install does not see DVSwitch networks

      I’ve just been handed an issue where, upon installing a VRA onto a group of ESX hosts (v5.5.u2) the VRA install wizard is unable to see the DVSwitch networks, only the standard switch networks. Networking on this host works as expected, otherwise.   Has anyone encountered this and if so, what was your solution? Regards, […]

    • People: 6
      Replies: 6
    • December 11, 2017
    • Change on CPU / Memory – replication

      Hi all,   Silly question –  If we change the number of CPUs in the production site, does it replicate automatically to the DR / destination site? Do we need to make anything to ensure the change?   We are on the middle of a Synch to a destination site and number of CPUs of […]

    • People: 3
      Replies: 3
    • December 6, 2017
    • Multiple ZVMs and on vCenter

      I am wondering if it is possible to have multiple ZVM setup in the same location, and sync’d to the same vCenter? With the ability to leverage the same storage and hypervisors as the first ZVM? The issue I am trying to get around is that the primary ZVM is having upgrade issues from 5.0 […]

    • People: 2
      Replies: 2
    • December 5, 2017
    • VRA not reporting VMs

      My customer has a remote site with a quite bad connection back to HQ. I managed to install VRAs on the hosts at the site, which took some hours, but the site’s virtual machines are not visible in the ZVM UI. The ZVM is located at HQ. I suspect the connection is the problem here. […]

    • People: 2
      Replies: 5
    • November 29, 2017
    • impact replication to os windows license

      Hi, I want to ask about windows license in virtual machine after live failover. whether to change the license of virtual machine or need a reactivate windows license after live failover? or the windows can run well? Thanks before.

    • People: 2
      Replies: 1
    • November 27, 2017
    • change protected site VRA?

      Hello, Is there any capability to move VM/VPG’s on protected site VRA’s like you can at the recovery site? Zerto does not do a good job of balancing VRA workloads and I would like to balance them out but cannot figure out a way in the UI.   Thanks

    • People: 2
      Replies: 2
    • November 20, 2017
1 2 3 … 28 29 30 … 35 36 37

You must be logged in to create new topics. Click here to login