• Protection of shared disk
    • Unable to run Zerto powershell cmdlets

      Hi, I am trying to run zerto powershell cmdlets. I am getting thesame  error while running any of the cmdlets Here are the error details Set-CheckPoint : System.ServiceModel.CommunicationException: An error occurred while receiving the HTTP response to http://10.0.xxx.xxx:9669/ZvmService/SiteController. This could be due to the service endpoint binding not using the HTTP protocol. This could also […]

      in: Scripting and APIs

    • People: 3
      Replies: 2
    • April 10, 2017
    • vCloud Director 8.2

      Now that VMware has announced GA for vCloud Director 8.2 will we see full support for it or will it require a workaround as before? VMware Announces General Availability of vCloud Director 8.20  

      in: VMware

    • People: 2
      Replies: 2
    • April 4, 2017
    • Unable to see multiple Clusters

      We are working a new install with a migration from a VMware 5.1 to a 6.5 Installation. The original setup uses 4 hosts for all guests, but the new setup has 8 hosts for protected operation guests (UCSDMZ) and 2 hosts for public access guests (PUBDMZ). When we set up VPG’s, we are only able […]

      in: VMware

    • People: 2
      Replies: 2
    • April 3, 2017
    • ESXi Patching and protecting VM's

      Hello! I’m going through my first ESXi patching round since deploying Zerto and I’m hoping there’s a better way to do it. Because of our SLA’s I can’t not protect VM’s while I’m patching hosts at DR or Production. I’m patching DR hosts currently and my process has been to change the recovery VRA via […]

      in: VMware

    • People: 3
      Replies: 2
    • March 30, 2017
    • Shadow VRA during upgrade

      What happens to the shadow VRA during an upgrade to a new version of Zerto?  I’m assuming while the VRAs get upgraded, the shadow VRA doesn’t need to be, as it’s just a place to mount vmdks?

      in: VMware

    • People: 2
      Replies: 1
    • March 27, 2017
    • Getting IP and Subnet

      Hi, I am writing a script to query Zerto for VM Source IP/Segment and also Target in DR after Fail Over same VM IP/Segment (since it might change). We didn’t find any way to do it with Zerto CLI. Can you help? Thanks Erez

      in: Scripting and APIs

    • People: 4
      Replies: 5
    • March 24, 2017
    • Start FailOverTest Powershell

      I unable to start failover test through Rest API here is my code $json=” { "CheckPointIdentifier“: "144321” }” Invoke-RestMethod -Uri $url -Body $json -Headers $zh -ContentType $TypeJSON -Method Post Error I am getting {“Message”:”failed parsing as a valid CheckPoint Identifier”}

      in: Scripting and APIs

    • People: 2
      Replies: 3
    • March 24, 2017
    • Managing Alerts Multi Peer sites

      Hello, I’m finishing up a Zerto 5u1 install. We have 3 vCenters at our protected site and 2 at our recovery site. I have alerting setup to send to my email address but will need to expand that to a larger group. I’m finding that I get a lot of duplicate alerts sent from various […]

      in: General Discussion

    • People: 2
      Replies: 2
    • March 23, 2017
    • Zerto VPG "Execute PS script"

      I am trying to execute a Powershell Script Pre or Post recovery ideally Post, but really im trying to figure out the syntax required to launch a script. In the Pre/Post Script config in the VPG there is command to runn and parramaters, i have tried multiple combinations to try to invoke a powershell script […]

      in: Scripting and APIs

    • People: 2
      Replies: 1
    • March 18, 2017
1 2 3 … 147 148 149 … 159 160 161