- This forum has 544 topics, 1,441 replies, and was last updated 3 hours, 36 minutes ago by Alisha K.
-
- VMware
-
-
upgrad esxi and mixed version
Hello, my customer want to upgrade esxi infrastructure Prod ( 16 nodes ) but no DR site. is it supported to have 2 site in DR, Prod esx 7.0u3 and DR 6.7U3 ? when I upgrade Prod it is supported have a cluster with node with different esxi version 6.7U3 and 7.0U3 managed by a […]
-
People: 1
Replies: 0 - February 15, 2023
-
Zerto protection for Linux clusters using RDM
Customer has a 3 node RHEL HA cluster with RDMs. The target will also be a cluster with RDM. Is Zerto replication supported in this environment? What are the system requirements it is supported
-
People: 1
Replies: 0 - February 5, 2023
-
Exclude large volume from replication
We have a few vm’s with very large volumes attached (in the 2TB range) and would like to protect the OS drive but not the cache drive(s). Is there a way to set up a VPG so that it excludes these drives? Setting them as Temp still causes the VPG to want to do an […]
-
People: 6
Replies: 5 - February 3, 2023
-
Documentation for slower VMs during test failover
Is there any official documentation that states why VM’s run slightly slower while doing a test failover? Need to have this documentation for compliance purposes and I can not find it anywhere.
-
People: 1
Replies: 0 - January 24, 2023
-
VM Version question
As we start to prepare for the Meltdown and Spectre remediation steps that need to be addressed I started to compile a list of virtual appliances that have a VM Version less than version 9 (there are vMotion issues once the patches start getting applied to the Hosts if your VM Version is below 9). […]
-
People: 1
Replies: 2 - January 9, 2023
-
VRA VM overrides – auto power on?
We are upgrading most of our infra from vSphere 6.0x to 6.5u1. One of the inconsistencies is whether VRA’s will automatically power on after the host comes back online. We are on Zerto 5.5u2p1. Most of our clusters all have VM Overrides set for each VRA to Disable both DRS automation and HA restart priority […]
-
People: 0
Replies: 0 - January 4, 2023
-
Understanding VPG storage sizes as reported by ZVM
We have been asked several times by clients what the Zerto storage values relate too and how they are calculated – hopefully this is useful to others…. When looking at the VPG details you will see that the ZVM reports back the following storage values, these values are also used in various reports and API […]
-
People: 2
Replies: 1 - January 4, 2023
-
Multiple vCenter replication pairs
Hello all, Could you guys please let me know how many Zerto nodes are required for the following setup: Number of sites: 3 (A, B, C). All sites are considered as active and recovery sites for one of the other two. Number of vCenter servers per site: 2 ( Management, Compute) I am planning to […]
-
People: 1
Replies: 2 - January 4, 2023
-
Leave Moved VMs powered off
We are migrating VMs from our Customers Site to our Site. How can I prevent the VMs from starting up automatically, after the move/failover?
-
People: 1
Replies: 2 - January 4, 2023
-
Z-VRA’s not powering down for host maintenance
When trying to remediate my ESXi hosts using Lifecycle Manager, the VRA’s are not powering down to allow the hosts to go into maintenance mode. If I manually place the host into maintenance mode, they power off. Anyone know a fix? vCenter – 7.0.3 Zerto – 9.0. U4
-
People: 3
Replies: 2 - January 3, 2023
-
DRS moving VMs to host before VRA is online
When we perform host maintenance, protected VMs are being moved to the hosts via DRS before the VRA is fully online. This is causing up to 2 hour delta syncs to happen before we can move on to the next host. Is there a way to prevent VMs from moving until the VRA is ready?
-
People: 2
Replies: 1 - December 13, 2022
-
VMware VM failover application Lincense
After VM failover application fails to run due to changed HardwareID and the installed license. How to get the hardware ID over with the VM?
-
People: 5
Replies: 4 - December 12, 2022
-
DR side VRA evacuate fails
vcenter 7.0up3g, Zerto 9.5 update 3, ESXi 7.0 up3 trying to evacuate and DR side host/vra give error: Failed to add disk scsi0:6. Object not found Cannot open (scsi # can be different) Zerto saying may be a VMware issue: message = “Object not found” – signalize that we can not find the disk, but […]
-
People: 1
Replies: 0 - November 21, 2022
-
Failover RecoverTime much longer than FailoverTest
We have an 11 VM VPG that will become accessible relatively quickly when we run our failover test. When we run an actual failover it takes about 90 minutes for all 11 VMs to come online. Can someone help me understand the different under hood on the recovery site when we run a failover test […]
-
People: 1
Replies: 3 - November 14, 2022
-
Zerto Compatibility with vCenter 7u3h / ESXi 7u3g?
Is Zerto compatible with the latest 7 releases? vCenter 7 Update 3h & ESXi 7 Update 3g? Running Zerto 9.5 Update 2. I can’t find the compatibility matrix, it used to be here: https://help.zerto.com/bundle/Operability.Matrix.HTML/
-
People: 3
Replies: 3 - November 1, 2022
-
upgrad esxi and mixed version
You must be logged in to create new topics. Click here to login