- This forum has 878 topics, 1,634 replies, and was last updated 11 hours, 10 minutes ago by Nana A.
-
- Support Q & A
-
-
host ESXi – change hardware / keep hostname
I need change hardware of the host ESXi and keep the hostname. Can you please advise what is the best practice the to do so?
-
People: 3
Replies: 2 - November 20, 2019
-
Quesiton about DisableCrossReplicationMonitor twea
We are looking into disabling the alert about the Microsoft Default SAN policy, as outlined in the Zerto article here: https://www.zerto.com/myzerto/knowledge-base/how-to-silence-vpg0043-error-the-microsoft-default-san-policy/ I just want to confirm that applying the tweak, “t_DisableCrossReplicationMonitor=1 “, only affects this specific alert. Does the “CrossReplicationMonitor” monitor anything else besides the possibility of the Microsoft Default SAN Policy causing disks to […]
-
People: 3
Replies: 2 - November 20, 2019
-
Replication history for deleted VPG
Posting on behalf of Jason C. Is there a way to identify the last time a VM or VPG was replicated after the VM/VPG has been deleted?
-
People: 2
Replies: 1 - November 20, 2019
-
How to calculate link between sites
Please could you help me how to calculate the necessary link between the main site and the site. Is there any tool to calculate?
-
People: 2
Replies: 1 - November 20, 2019
-
Export VPG settings readable format
hi guys is there a way to export settings for each VPG, VM Name, datastores, Disk marked as Temp Disk, PortGroups, and IPs? I know I can export VPGs setting user Zerto Config but that is not readable format I have a Window for this customer and in case some VPGs fails I just want […]
-
People: 2
Replies: 3 - November 20, 2019
-
Keep alerts enabled/disabled while upgrading ZVM
Whenever we upgrade ZVM and VRAs, all the custom alarms get reset and we start getting flooded with unwanted alerts. Is there a way to maintain the old alarm configuration and status. We want disabled alerts to remain disabled and enabled to be enabled after upgrade.
-
People: 2
Replies: 1 - November 20, 2019
-
StoreOnce setup
We are setting up our StoreOnce for long term storage to get ready for our Zerto 7.5 install (We do not have Zerto setup yet). Will we set up a Catalyst repository on the StoreOnce or would we be using NAS or VTL? We will be backing up Hyper-V VMs and replicating them to an […]
-
People: 2
Replies: 3 - November 19, 2019
-
protect vm from single ESXi host to ZVM
i want protect (create VPG) a VM from the single independent esxi host (seperate from VCenter and no ZCM) to different vcenter zerto site( where ZCM and ZVM insatlled) this is can I protect Vm from ESXi host (without ZCM) to vcenter (ZCM ) site?
-
People: 2
Replies: 1 - November 19, 2019
-
VM's still replicating when powered off
We are a cloud provider and from time to time, our ZVM does not show that the production environment VM is powered off.. We are currently protecting a set of VMs in our own environment that are powered off, however the ZVm is not reflecting that. Should it still be replicating powered off VM’s or […]
-
People: 2
Replies: 1 - November 19, 2019
-
Using Zerto to migrate a large VM
We have a large VM that will need to be powered down to VMotion. However I want to use Zerto to replicate the VM then once powered down I want to initiate a failover to then bring it up on the new storage in the new cluster. I wanted to check with Zerto on that […]
-
People: 3
Replies: 3 - November 19, 2019
-
Export Settings for VPGs
is there a way to export settings for each VPG, VM Name, datastores, Disk marked as Temp Disk, PortGroups, and IPs? I know I can export VPGs setting user Zerto Config but that is not readable format I have a Window for this customer and in case some VPGs fails I just want to have […]
-
People: 2
Replies: 1 - November 19, 2019
-
FOT vs live failover
What is the difference between a test failover and a live failover? Will both do a reverse delta sync?
-
People: 2
Replies: 1 - November 18, 2019
-
Zerto Cloud Manager OS upgrade
We have ZCM 6.5 running on Windows 2008 R2. Does ZCM support an in-place OS upgrade from win 2008R2 to win 2012 R2?
-
People: 2
Replies: 3 - November 18, 2019
-
ZVM reinstall
Hi I want to know what will be happening if I reinstall ZVM for new VM? Do I need to install new VRA and VPGs? or remain?
-
People: 1
Replies: 1 - November 18, 2019
-
Syslog Integration
Posted on behalf of Matthew H. Does Zerto have easy integration with Rapid 7 (or other SIEMs/syslog) for log collection?
-
People: 2
Replies: 2 - November 15, 2019
-
host ESXi – change hardware / keep hostname
You must be logged in to create new topics. Click here to login